SYSTEMATIC STUDY OF CADMIUM SELENIDE NANOSTRUCTURE GROWTH GUIDES FUTURE EFFORTS
27 October 2005 - Georgia Institute of Technology

Using the results from more than 150 different experiments in which temperature and pressure conditions were systematically varied, nanotechnology researchers at the Georgia Institute of Technology created a "road map" to guide future nanomanufacturing using the vapor-liquid-solid technique.

The results, reported this month in the journal Advanced Materials, join earlier Georgia Tech work that similarly mapped production conditions for nanostructures made from zinc oxide, an increasingly important nanotechnology material. Together, the two studies provide a foundation for large-scale, controlled synthesis of nanostructures that could play important roles in future sensors, displays and other nanoelectronic devices.

The research was supported by the National Science Foundation, the NASA Vehicle Systems Program, the Department of Defense Research and Engineering and the Defense Advanced Research Projects Agency.

"For the future of nanomanufacturing, we needed a systematic map to show the best conditions for producing these structures reproducibly with high yield," explained Zhong Lin Wang, director of Georgia Tech's Center for Nanoscience and Nanotechnology. "This information will be necessary for scaling up the production of these interesting structures for the applications that will be developed."

In work that required more than a year to complete, Wang and collaborator Christopher Ma collected information on more than 45 separate combinations of growth conditions governing the production of cadmium selenide nanostructures. In their experimental set-up, powdered cadmium selenide was heated to hundred of degrees Celsius in a simple horizontal tube furnace under the flow of nitrogen gas, using gold as a catalyst.

The technique produced three different types of nanostructures:

• "Nanosaws/nanocombs," unusual structures that form with "teeth" on one side and a smooth surface on the other;
• "Nanobelts," which are ribbon-like structures, and
• "Nanowires" that resemble grass and grow vertically from the substrate.

The researchers varied the temperature at the cadmium selenide source, the temperature of the silicon substrate where the structures grew, and the gas pressure inside the furnace. They repeated each experimental condition three times, each time determining where the structures grew on the substrate and counting the number of nanosaws/nanocombs, nanobelts and nanowires in samples that were examined with electron microscopy.

"These three different structures are all produced using the same general experimental conditions, but somehow you get different percentages of each," Wang said. "Our goal was to determine how to control the conditions to learn how to get close to 100 percent yield of each structure. This required a systematic study of the experimental conditions."

Each experiment required approximately two days to produce the structures and analyze the samples.

Based on their experimental work, Wang and Ma mapped the optimal conditions for producing each of the three structures, and learned more about the fabrication process. For instance, they found that growth of the nanostructures is primarily controlled by the nitrogen gas pressure inside the chamber and the temperature of the substrate where the structures are deposited. They also learned where each type of structure was likely to be deposited on the substrate under each set of conditions.

Cadmium selenide nanosaws and nanocombs are the most finicky to grow. At the other end of the scale, nanowires can be produced from cadmium selenide at a broad range of temperature and pressure conditions. Specifically, the researchers reported:

• Lower temperatures at the source material (630 degrees C), higher pressures (600 millibars) and substrate temperatures of approximately 575 degrees C produce the highest percentage of nanosaws and nanocombs.
• Lower temperatures at the source material (700 degrees C), lower chamber pressures (4 millibars) and substrate temperatures of approximately 575 degrees C produce the highest percentage of nanobelts.
• Growth of nanowires can be carried out at a broad range of temperatures and pressures, with higher source temperatures favoring the growth of nanowires over nanosaws.

"If other groups want to produce these structures, they can use our plots to determine the pressures that will be required, the temperatures and the locations within the chamber where they will grow," Wang said. "Until now, researchers have had to determine these parameters by trial and error."

Cadmium selenide has been studied for applications in optoelectronics, luminescent materials, lasing materials and biomedical imaging. It is perhaps best known as the basis for quantum dots that have applications in biomedical imaging.

http://www.gatech.edu

More News:
  • For October 2005
  • From Georgia Institute of Technology
  • For University