Free Newsletter
Register for our Free Newsletters
Newsletter
Zones
Advanced Composites
LeftNav
Aerospace
LeftNav
Amorphous Metal Structures
LeftNav
Analysis and Simulation
LeftNav
Asbestos and Substitutes
LeftNav
Associations, Research Organisations and Universities
LeftNav
Automation Equipment
LeftNav
Automotive
LeftNav
Biomaterials
LeftNav
Building Materials
LeftNav
Bulk Handling and Storage
LeftNav
CFCs and Substitutes
LeftNav
Company
LeftNav
Components
LeftNav
Consultancy
LeftNav
View All
Other Carouselweb publications
Carousel Web
Defense File
New Materials
Pro Health Zone
Pro Manufacturing Zone
Pro Security Zone
Web Lec
Pro Engineering Zone
 
 
 
News

Design tip: building better bosses

Proto Labs : 12 August, 2013  (Technical Article)
A boss is a feature raised above a surface. In plastic parts, bosses are typically used to assist in assembly, as a receptacle for a screw or threaded insert or as the locator for a mating pin on another part.
Design tip: building better bosses

Because of its function, a boss must have sufficient strength to do its job. This dictates a minimum size for the feature. At the same time, because a boss rises from a surface, it thickens the surface at that point raising the risk of sink or development of voids as the part cools. The challenge: bosses should be big enough to do their job but not big enough to cause avoidable sink in the surface from where they rise.

A typical boss is an open-topped cylinder, essentially a round rib (see Figure 1a). Standard guidelines suggest that its wall thickness be between 40 and 60 percent of the thickness of the wall from which the boss rises. If your design requires more strength than this guideline would provide, you should consider ways to strengthen the boss without thickening its walls. The most common of these is to surround the boss with gussets to support and strengthen its walls (see Figure 1b).

If a boss is part of a vertical wall, it should not create a thick area in the wall. Figure 1c shows an example of how this can be done. Similarly, if a boss is located close to a vertical wall, it may be tempting to tie the boss to the wall by filling the space between the boss and the wall, resulting in a thick area (see Figure 1d). A better way to tie the boss to the wall is with one or more ribs (see Figure 1e).

 

In some cases, Protomold’s milling process may require that the walls of the boss be thicker than the standard 40 to 60 percent mentioned above. Protomold generally forms both the outside diameter and the inside diameter of a boss with features of the aluminium mould. When cutting a mould for a relatively tall boss, we may not be able to use a sufficiently small-diameter cutter to create walls that thin. You can avoid the problem by reducing the height of the boss, allowing the use of smaller-diameter cutter. Or you may find that a small amount of sink in the wall surface opposite the boss is acceptable.

There are two additional points to consider in designing bosses. As mentioned earlier, a boss is a circular rib, and like any rib, its walls—both inside and out—must be drafted to facilitate ejection. Depending on the height of the boss, this draft can be anywhere from ½ to 3 degrees. If draft of the inside diameter of the boss is not acceptable, then Protomold may be able to use a selection of standard diameter undrafted steel core pins, similar to those that would be used in steel tools. If applicable these will be highlighted in your quote or please speak to your customer service engineer for further details. Alternatively the boss can be moulded as a solid and the inside diameter drilled, by you, as a secondary operation.

Also, because a boss is formed by a blind hole in the mould body, we may have to add vent pins to the rim of the boss to allow the escape of trapped gas during mould filling. Otherwise shorts or burns may form on the rim.

Bookmark and Share
 
Home I Editor's Blog I News by Zone I News by Date I News by Category I Special Reports I Directory I Events I Advertise I Submit Your News I About Us I Guides
 
   © 2012 NewMaterials.com
Netgains Logo